Electrolux Washer Error Codes

Below is a complete list of Electrolux Washer error codes, what each code means, and the issues they typically indicate.

Error Code	Description
01E	The washer detected insufficient water flow during filling.
02E	The washer detected a heating system malfunction.
03E	The washer detected a drain system malfunction.
07E	The washer detected a temperature sensor (NTC) fault.
1	The washer did not detect water entering the machine.
10	The washer detected that the motor is not running when commanded.
10E	The washer detected a motor system malfunction.
11	The motor failed to reach the programmed speed.
12	The motor exceeded the safe speed limit.
13	The washer detected a tachometer signal fault.
14	The washer detected motor overheating.
15	The washer detected that the motor is stalled.
16	The washer detected irregular drum rotation.
17	The washer detected an unbalanced load.
18	The washer did not drain within the expected time.
19	The washer detected a water level sensor fault.
2	The washer detected that the door is open.
20	The washer detected low water level during heating.
21	The washer detected a heating element malfunction.
22	The washer detected an out-of-range temperature sensor reading.
23	The washer detected a heating relay malfunction.
24	The washer's heating safety cutoff has been triggered.
25	The washer detected excessive water level during heating.
26	The washer detected an unexpected drop in water level.
27	The washer detected a general overfill condition.
28	The washer detected a general underfill condition.
29	The washer detected a calibration error in the water level sensor.
3	The washer cannot lock the door.
30	The washer detected an electrical fault in the water level sensor circuit.
31	The washer detected a communication fault between control boards.
32	The washer detected a memory fault in the control board.
33	The washer detected an invalid or missing configuration.
34	The washer cannot communicate with the motor inverter.
35	The washer detected an inverter malfunction.
36	The washer detected a missing or incorrect motor phase.
37	The washer detected excessive motor current.
38	The washer detected insufficient motor current.
39	The washer detected invalid motor speed sensor feedback.
4	The washer cannot unlock the door.
40	The washer detected an overvoltage condition.
41	The washer detected an undervoltage condition.
42	The washer detected a phase imbalance or missing phase.
43	The washer detected an internal control board malfunction.
5	The washer detected an excessively high water level.
6	The washer did not reach the programmed water level.
7	The washer failed to heat water within the expected time.
8	The washer detected overheating.
9	The washer detected a motor overload condition.
E10	The washer is not receiving water at the expected rate.
E11	The washer did not fill with water during the wash phase.
E12	The washer did not fill with water during the rinse phase.
E13	The washer detected water loss during the cycle.
E20	The washer is draining too slowly or not at all.
E21	The washer detected slow or incomplete draining.
E22	The washer did not drain after the rinse cycle.
E23	The control board detected a drain pump triac sensing fault.
E24	The control board detected a drain pump triac circuit failure.
E25	The control board received an invalid or unexpected signal.
E31	The pressure sensor is reporting invalid or unstable water level readings.
E32	The pressure sensor calibration is incorrect or out of range.
E35	The washer detected an excessively high water level.
E40	The washer detected a general door lock system fault.
E41	The washer detected that the door is not closed.
E42	The washer cannot lock the door.
E43	The control board detected a door lock triac fault.
E44	The washer is not receiving proper feedback from the door lock.
E45	The control board’s door lock circuit has failed.
E50	The washer detected a general motor system fault.
E60	The washer detected a general heating system fault.
E61	The washer failed to heat water to the required temperature.
E62	The washer detected that water temperature is too high.
EC1	The washer received an incorrect signal from the flow meter.
EF1	The washer detected a drain pump or filter blockage.
EF2	The washer detected excessive foam inside the drum.
EF4	The flow meter is not detecting water flow.
EF5	The washer detected an out-of-balance condition.
EH0	The washer detected an electrical supply irregularity.