What are the symptoms of error code LE?

Washer will not spin or agitate, Washer hums briefly and then stops, Cycle stops mid‑wash or mid‑spin, ThinQ may show 'Motor error' or 'Motor not turning', Drum feels stiff or jammed when rotated by hand

What causes error code LE?

Failed hall sensor (motor position sensor), Loose or damaged wiring between motor and control board, Overloaded drum, Foreign object jammed between tub and drum, Seized drum bearings, Failed drive motor (less common), Faulty main control board (rare)

How do I fix error code LE?

Unplug the washer for 10 minutes to reset the control., Reduce the load and run a test cycle., Inspect the hall sensor connector for looseness or corrosion., Check the motor harness for damage., Rotate the drum by hand to check for binding., Test the hall sensor and replace if out of spec., Replace the drive motor if it fails continuity or rotation tests., If all components test good, suspect the main control board.

LG Washer - LE Error Code

The washer detected a locked or stalled motor.

Meaning

The washer detected a locked or stalled motor.

The LG LE error code indicates that the drive motor is unable to rotate properly. On LG Direct‑Drive washers, the control board monitors motor current and hall sensor feedback. If the drum does not turn as expected or the motor draws excessive current, the washer stops the cycle and displays LE. This code is used across all LG Direct‑Drive front‑load, Direct‑Drive top‑load, ThinQ, and Giant/Titan commercial washers in North America.

Symptoms

Washer will not spin or agitate
Washer hums briefly and then stops
Cycle stops mid‑wash or mid‑spin
ThinQ may show 'Motor error' or 'Motor not turning'
Drum feels stiff or jammed when rotated by hand

Causes

Failed hall sensor (motor position sensor)
Loose or damaged wiring between motor and control board
Overloaded drum
Foreign object jammed between tub and drum
Seized drum bearings
Failed drive motor (less common)
Faulty main control board (rare)

🔧

Step-by-Step Fixes

Unplug the washer for 10 minutes to reset the control.
Reduce the load and run a test cycle.
Inspect the hall sensor connector for looseness or corrosion.
Check the motor harness for damage.
Rotate the drum by hand to check for binding.
Test the hall sensor and replace if out of spec.
Replace the drive motor if it fails continuity or rotation tests.
If all components test good, suspect the main control board.

⚠️

Safety Notes

Disconnect power before accessing the motor or control board.
Do not continue running the washer if you smell burning or hear grinding.
Avoid chronic overloading, as it accelerates wear on the motor and bearings.

📋

Applicable Models

Show Models

[Giant-C Giant-V Titan-C Titan-V]
map[front-load direct-drive:[WM2101HW WM2487HRM WM2501HVA WM2701HV WM3050CW WM3070HWA WM3170CW WM3370HWA WM3470HVA WM3500CW WM3550HVA WM3570HVA WM3600HWA WM3700HWA WM3800HBA WM3900HWA WM4000HWA WM4000HBA WM4200HWA WM4500HBA WM5000HVA WM5100HVA WM5500HVA WM6500HWA WM6700HBA WM8100HVA WM9000HVA] top-load direct-drive:[WT1101CW WT1201CV WT1501CW WT1701CV WT1901CW WT7100CW WT7200CW WT7300CW WT7400CV WT7500CW WT7800CW WT7900HBA WT7150CW WT7405CW WT8100HVA WT8200CV WT8400CV WT8600HVA]]

📁

Other LG Washer Error Codes

Show All Error Codes

Model-Specific Notes

- LE is overwhelmingly caused by hall sensor failure on Direct‑Drive models. - ThinQ models may show “Motor not turning” or “Motor error” instead of LE. - Commercial Giant/Titan units log LE as a motor rotation fault in service mode. - If the drum is difficult to rotate by hand, suspect seized bearings or a foreign object.

Disclaimer

The information provided on this page is for educational and informational purposes only. Repairs involve electrical, mechanical, and water-related risks. Always follow manufacturer instructions and consider contacting a qualified technician for diagnosis or repair.