Maytag Washer - F3E5 (Front-Load) Error Code

Water level system error --- pressure sensor readings are invalid or inconsistent.

Meaning

Water level system error --- pressure sensor readings are invalid or inconsistent.

The Maytag F3E5 error code on front-load washers indicates that the appliance control unit (ACU) is receiving invalid, inconsistent, or out-of-range signals from the water level pressure sensor. Whirlpool-built Maytag front-load washers use an analog pressure transducer to monitor water level throughout the wash cycle. If the sensor voltage is unstable, the hose is blocked, or the ACU detects impossible water-level transitions, it triggers F3E5 to prevent overfilling or incorrect cycle operation.

Symptoms

  • Washer stops mid-cycle with F3E5
  • Washer fills too little or too much
  • Cycle will not start or stalls during sensing
  • Washer drains unexpectedly or repeatedly
  • Intermittent water-level related faults

Causes

  • Blocked or kinked pressure hose (most common)
  • Water trapped in the pressure hose
  • Failed pressure sensor (analog transducer)
  • Loose or corroded pressure-sensor wiring
  • Detergent residue buildup in the air dome
  • ACU misreading sensor voltage due to wiring resistance issues
πŸ”§

Step-by-Step Fixes

  • Unplug the washer for 5 minutes to reset the ACU.
  • Inspect the pressure hose for kinks, pinches, or blockages.
  • Remove the pressure hose and blow through it to clear trapped water or debris.
  • Check the pressure sensor connector for corrosion or loose pins.
  • Inspect the air dome on the tub for detergent residue buildup.
  • Replace the pressure sensor if voltage readings are unstable.
  • If wiring and sensor test good, replace the ACU.
⚠️

Safety Notes

  • Disconnect power before accessing internal wiring or the pressure sensor.
  • Do not operate the washer if overfilling or underfilling occurs.
  • Avoid excessive detergent use, which can clog the air dome.
πŸ“‹

Applicable Models

Show Models
  • MHW3000 Series: MHW3000BW, MHW3100DW
  • MHW3500 Series: MHW3500FW, MHW3505FW
  • MHW4200 Series: MHW4200BW
  • MHW4300 Series: MHW4300DW
  • MHW5100 Series: MHW5100DW
  • MHW5500 Series: MHW5500FW, MHW5500DW
  • MHW5630 Series: MHW5630HW, MHW5630HC
  • MHW6000 Series: MHW6000XW
  • MHW6630 Series: MHW6630HW, MHW6630HC
  • MHW7000 Series: MHW7000XW
  • MHW7100 Series: MHW7100DW
  • MHW8200 Series: MHW8200FW
  • MHW8630 Series: MHW8630HW, MHW8630HC
  • MHW9000 Series: MHW9000YW, MHW9000XL, MHW9000XR
  • MHWE Series: MHWE200XW, MHWE201YW, MHWE251YG, MHWE251YW, MHWE301YG, MHWE301YW
  • MHWZ Series: MHWZ400TQ, MHWZ600TW
  • Commercial Front-Load: MLG2000AWW, MLG3000AWW, MLG4500 Series
πŸ“

Related Pages

πŸ“

Other Maytag Washer Error Codes

Show All Error Codes

Model-Specific Notes

On modern MHW-series front-load washers, F3E5 is most commonly caused by a blocked pressure hose or a failing pressure transducer. On older MHWE and MHWZ models, detergent residue buildup in the air dome frequently leads to water-level system errors.

Disclaimer

The information provided on this page is for educational and informational purposes only. Repairs involve electrical, mechanical, and water-related risks. Always follow manufacturer instructions and consider contacting a qualified technician for diagnosis or repair.

Copyright 2026. All rights reserved.