Maytag Washer - F5E4 (Top-Load) Error Code

Lid not opened between cycles --- washer requires the lid to be opened before starting a new cycle.

Meaning

Lid not opened between cycles --- washer requires the lid to be opened before starting a new cycle.

The Maytag F5E4 error code on top-load washers indicates that the appliance control unit (ACU) detected that the lid was not opened after the previous cycle completed. Whirlpool-built Maytag top-load washers require the lid to be opened between cycles to ensure that the user has removed or adjusted the load, added detergent properly, and acknowledged the end of the previous cycle. If the lid remains closed when a new cycle is requested, the control triggers F5E4 to prevent accidental rewash or unsafe operation.

Symptoms

  • Washer will not start a new cycle
  • F5E4 appears immediately after pressing Start
  • Washer beeps but does not proceed to sensing
  • Washer seems unresponsive until lid is opened
  • Cycle resets after lid is opened

Causes

  • Lid was not opened after the previous cycle
  • Lid switch stuck in the 'closed' position
  • Faulty lid-lock assembly reporting incorrect state
  • Misaligned lid strike preventing proper state change
  • Wiring harness issues causing incorrect lid-state feedback
  • ACU misinterpreting lid-state transitions
πŸ”§

Step-by-Step Fixes

  • Open the lid fully, wait 1---2 seconds, then close it again.
  • Ensure the lid hinge is not binding and can open freely.
  • Inspect the lid strike for proper alignment with the lock sensor.
  • Check the lid-lock assembly for mechanical sticking.
  • Inspect the lid-switch wiring harness for loose or damaged connectors.
  • Replace the lid-lock assembly if it cannot detect lid-state changes.
  • Replace the ACU only after confirming switch and wiring integrity.
⚠️

Safety Notes

  • Disconnect power before servicing the lid lock or wiring.
  • Do not bypass the lid switch; it is a critical safety component.
  • Avoid forcing the lid open or closed, as this can damage hinges or the strike.
πŸ“‹

Applicable Models

Show Models
  • Modern HE Top-Load (No Agitator): MVWB835DW, MVWB835DC, MVWB865GW, MVWB865GC, MVWB766FW, MVWB766FC, MVWB725BW, MVWB725BC, MVWB750YW, MVWB750WB, MVWB880BW, MVWB880WC
  • Modern HE Top-Load With Agitator: MVW6230HW, MVW6230RHW, MVW6230HC, MVW7230HW, MVW7230HC, MVW7232HW, MVW7232HC, MVW6200KW, MVW6200KG, MVW6500MBK, MVW6500MW, MVW5035MW, MVW5030MW, MVW5430MW
  • Bravos Series (HE Top-Load): MVWB300BW, MVWB300WQ, MVWB300VW, MVWB400BW, MVWB400VQ, MVWB400VW, MVWB450BW, MVWB450WQ, MVWB450VW, MVWB700VQ, MVWB700BW, MVWB700VW, MVWB750YW, MVWB750WB, MVWB850YW, MVWB850WB
  • Centennial Series (HE Top-Load): MVWC400XW, MVWC400VW, MVWC500XW, MVWC500VW, MVWC565FW, MVWC565FW1, MVWC565FW2
  • Commercial Technology Top-Load: MVWC565FW, MVWC565FW1, MVWC565FW2, MVWC6ESWW, MVWC6ESW1
  • Maytag 3000 Series (Top-Load HE): MVWB300WQ, MVWB300BW, MVWB300VW
  • Maytag 4000 Series (Top-Load HE): MVWB400VQ, MVWB400BW, MVWB400VW
  • Maytag 5000 Series (Top-Load HE): MVWB500WQ, MVWB500BW, MVWB500VW
  • Maytag 6000 Series (Top-Load HE): MVWB600WQ, MVWB600BW, MVWB600VW
  • Additional Verified F-Code Top-Load Models: MVW18MNBGW, MVW18MNBGW1, MVW20MNBGW, MVW20MNBGW1
πŸ“

Related Pages

πŸ“

Other Maytag Washer Error Codes

Show All Error Codes

Model-Specific Notes

On modern MVW and MVWB HE top-load washers, F5E4 is most commonly caused by the lid not being opened after the previous cycle. On older Bravos and Centennial models, sticky lid switches and worn hinges frequently prevent proper lid-state transitions.

Disclaimer

The information provided on this page is for educational and informational purposes only. Repairs involve electrical, mechanical, and water-related risks. Always follow manufacturer instructions and consider contacting a qualified technician for diagnosis or repair.

Copyright 2026. All rights reserved.