What are the symptoms of error code nd?

Washer stops mid-cycle with water still inside, Washer will not enter spin mode, Washer repeatedly attempts to drain, Washer displays nd and refuses to continue, Front-load models may hum loudly from the pump, Top-load models may hum with no water movement

What causes error code nd?

Clogged drain pump filter (front-load models), Blocked drain pump impeller, Kinked or restricted drain hose, Drain hose inserted too far into standpipe causing siphoning, Failed drain pump motor, Blocked tub-to-pump hose (coins, socks, debris), Pressure hose blocked or full of suds, Wiring harness issues at the pump, Control board unable to detect water level changes

How do I fix error code nd?

Check for standing water and attempt a drain/spin cycle., Inspect the drain hose for kinks or restrictions., Ensure the drain hose is not inserted more than 4.5---6 inches into the standpipe., On front-load models, remove and clean the drain pump filter., Check the tub-to-pump hose for blockages., Test the drain pump for proper operation and resistance., On top-load models, inspect the pressure hose for blockages or suds buildup., Replace the drain pump if it fails testing., If all components test good, inspect the control board for relay failure.

Maytag Washer - nd Error Code

The washer is not draining water.

Meaning

The washer is not draining water.

The Maytag nd error code indicates that the washer did not drain within the expected time. This code appears across multiple Maytag platforms, including front-load MAH models, top-load Bravos/Bravos XL/Centennial/VMW models, and Neptune TL washers. While the drain systems differ---front-load models use a pump with a filter, top-load models use a direct drain pump without a filter, and Neptune TL uses a high-flow pump---the meaning is identical: the control did not detect water leaving the tub fast enough. This can be caused by blockages, pump failures, wiring issues, or siphoning problems.

Symptoms

Washer stops mid-cycle with water still inside
Washer will not enter spin mode
Washer repeatedly attempts to drain
Washer displays nd and refuses to continue
Front-load models may hum loudly from the pump
Top-load models may hum with no water movement

Causes

Clogged drain pump filter (front-load models)
Blocked drain pump impeller
Kinked or restricted drain hose
Drain hose inserted too far into standpipe causing siphoning
Failed drain pump motor
Blocked tub-to-pump hose (coins, socks, debris)
Pressure hose blocked or full of suds
Wiring harness issues at the pump
Control board unable to detect water level changes

🔧

Step-by-Step Fixes

Check for standing water and attempt a drain/spin cycle.
Inspect the drain hose for kinks or restrictions.
Ensure the drain hose is not inserted more than 4.5---6 inches into the standpipe.
On front-load models, remove and clean the drain pump filter.
Check the tub-to-pump hose for blockages.
Test the drain pump for proper operation and resistance.
On top-load models, inspect the pressure hose for blockages or suds buildup.
Replace the drain pump if it fails testing.
If all components test good, inspect the control board for relay failure.

⚠️

Safety Notes

Disconnect power before accessing the drain pump or hoses.
Be prepared for water spillage when removing hoses or filters.
Avoid excessive detergent use, which can cause suds-related drain issues.

📋

Applicable Models

Show Models

Front-Load Maytag MAH Series: MAH3000AWW, MAH4000AWW, MAH5500AWW, MAH6500AWW, MAH7500AWW, MAH8700AWW, MAH9700AWW
Top-Load Maytag Bravos Series: MVWB300WQ, MVWB400VQ, MVWB450WQ, MVWB700VQ, MVWB750WQ, MVWB850YW, MVWB880BW, MVWB950YG
Top-Load Maytag Bravos XL Series: MVWB725BW, MVWB835DW, MVWB855DC, MVWB855DW, MVWB950YW
Top-Load Maytag Centennial Series: MVWC300BW, MVWC350BW, MVWC360FW, MVWC415EW, MVWC425BW, MVWC565FW, MVWC575FW
Top-Load Maytag Early VMW Series: MVWC6ESWW, MVWC700VW, MVWC700VQ, MVWC7000WQ, MVWC7000XW, MVWC7000YW, MVWC750YW
Top-Load Maytag Neptune TL Series: FAV6800AWW, FAV9800AWW

📁

Other Maytag Washer Error Codes

Show All Error Codes

Model-Specific Notes

Front-load models commonly trigger nd due to clogged pump filters or blocked tub-to-pump hoses. Bravos, Centennial, and VMW top-load models typically experience nd due to pump motor failure, drain hose issues, or pressure hose blockages. Neptune TL models use a high-flow pump that can fail due to debris or worn impellers.

Disclaimer

The information provided on this page is for educational and informational purposes only. Repairs involve electrical, mechanical, and water-related risks. Always follow manufacturer instructions and consider contacting a qualified technician for diagnosis or repair.