Maytag Washer - tE Error Code

The washer detected a temperature sensor problem.

Meaning

The washer detected a temperature sensor problem.

The Maytag tE error code indicates that the washer detected a problem with the temperature sensor or the water temperature reading. This code appears across multiple Maytag platforms, including front-load MAH models, Bravos/Bravos XL/Centennial/VMW top-load models, and Neptune TL washers. While the sensing hardware differs---front-load models use a thermistor in the heater or inlet system, top-load models use a temperature sensor integrated into the inlet valve or control board, and Neptune TL uses a tub thermistor---the meaning is identical: the washer is receiving an invalid, out-of-range, or missing temperature signal.

Symptoms

  • Washer stops mid-cycle and displays tE
  • Washer fills but will not advance
  • Washer drains and stops unexpectedly
  • Water temperature seems incorrect
  • Washer may repeatedly attempt to fill or adjust temperature

Causes

  • Faulty temperature sensor (thermistor)
  • Loose or corroded wiring harness connections
  • Failed inlet valve temperature sensor (top-load models)
  • Shorted or open thermistor circuit
  • Control board unable to read temperature input
  • Incorrect water temperature due to plumbing issues
πŸ”§

Step-by-Step Fixes

  • Unplug the washer for 1 minute to reset the control.
  • Inspect wiring harness connections at the thermistor or inlet valve.
  • Test the thermistor for proper resistance (typically 10k-- at room temperature).
  • On top-load models, test the inlet valve temperature sensor.
  • Ensure hot and cold water lines are connected correctly.
  • Replace the thermistor or inlet valve if readings are out of range.
  • If the sensor tests good, inspect the control board for input circuit failure.
⚠️

Safety Notes

  • Disconnect power before testing electrical components.
  • Avoid touching wiring with wet hands.
  • Do not run the washer with disconnected sensors.
πŸ“‹

Applicable Models

Show Models
  • Front-Load Maytag MAH Series: MAH3000AWW, MAH4000AWW, MAH5500AWW, MAH6500AWW, MAH7500AWW, MAH8700AWW, MAH9700AWW
  • Top-Load Maytag Bravos Series: MVWB300WQ, MVWB400VQ, MVWB450WQ, MVWB700VQ, MVWB750WQ, MVWB850YW, MVWB880BW, MVWB950YG
  • Top-Load Maytag Bravos XL Series: MVWB725BW, MVWB835DW, MVWB855DC, MVWB855DW, MVWB950YW
  • Top-Load Maytag Centennial Series: MVWC300BW, MVWC350BW, MVWC360FW, MVWC415EW, MVWC425BW, MVWC565FW, MVWC575FW
  • Top-Load Maytag Early VMW Series: MVWC6ESWW, MVWC700VW, MVWC700VQ, MVWC7000WQ, MVWC7000XW, MVWC7000YW, MVWC750YW
  • Top-Load Maytag Neptune TL Series: FAV6800AWW, FAV9800AWW
πŸ“

Related Pages

πŸ“

Other Maytag Washer Error Codes

Show All Error Codes

Model-Specific Notes

Front-load models typically trigger tE due to a failed drum thermistor or wiring issue. Bravos, Centennial, and VMW top-load models often trigger tE due to a faulty inlet valve temperature sensor or wiring harness problem. Neptune TL models use a tub thermistor that may fail due to moisture intrusion or age.

Disclaimer

The information provided on this page is for educational and informational purposes only. Repairs involve electrical, mechanical, and water-related risks. Always follow manufacturer instructions and consider contacting a qualified technician for diagnosis or repair.

Copyright 2026. All rights reserved.